Short connect boot pin to ground should work, please double check if you need.
Yes, good luck with the coding work, we can only provide very limit help on this. But any hardware questions please always let us know.
Thanks. Best regards,
Hi,
We are not that good at code, and can only provide simple demo for it. For the CAD mode, we are not sure about it, please try by yourself. SPI Flash is for storing the mass data.
Hi,
The question is to elimate the push button action right? You can find the boot pin, and solder it to ground, then will auto start when power up. (also can de-solder the boot key, and short connect the boot
Hi,
Yes, demo code in our bitbucket, will email you the credential.
Power LED about
Hello all,
The flash also need to be iniateed well, otherwise if only power but not operate, will cost up to 700uA
Hi,
1 and 2 can be done by software, we only work on hardware, can not help you with this, it is simple, should be easy to done it.
3. Yes, each channel of RGB are connectd to module each IOs, you can control each IO to do so, also very simple controlling
Hi,
What is CAD mode? What we can do on hardware to help on this? Please let mek now, thanks.
power LED no problem, this is a demo board, we can just do not place the led during production. b
Should only clamp one wire of the AC power wires, not two, please notice, otherwise will be no output. You can google some images to get a clear understanding.
Good to know getting better, you can try the LCD 5110 or SPI LCD onto the shield, and use external power supply. It is much more easy to monitor.
We tested this with a hair dryer, about 2-10A, but the output ranging is not a lot, probably need more code work. If you have any su
Hi,
The 100A sensor has too large range normally used for big devices or buiding, if the input is a few amps it won't change a lot, maybe you can try the 30A version.
Also make sure all the settings in the sketch is correct, make sure the setup is for 100a not 30a, you ca
Hi,
We are not desginer of this, also not good at this :( Also only resell this.
Please post the question to espressif forum here, https://bbs.espressif.com/ or maybe their github
Hi, sorry this forum don't have notice function.
Sorry for the wiki problem, if you have any help need you can put on here or write us email. We do best to help!Thanks.
If I compare correct, pro mini use regualtor MIC2505, which quiescent current is 5uA, but only 150mA delivery, the upgrade version MIC2519 is better 8uA/500mA. Our current use is AP2112 but 55uA quiescent and output up to 500mA. Which also add this to test later.
If not received the email, please drop email to info@electrodragon.com.
Hi, please check the tracking info email, it embedds with the wiki login info for 2-3 months, then you can view all wiki info.
Some wiki info is we collected but maybe not authroized (we collected a lot), to avoid troubles and also copy, we do in this way.
Th
We will keep doing this test, with lowpower library too.
Any suggesttions. or test need please let us know we will do. Any updates will update this thread and also on wiki.
we have just done some test today, result is here.
http://www.electrodragon.com/w/Low_Power
On transmitter mode, should be 9.5mA regular standby, remove all extras, can reduce about 4 mA maxium.
Hi, the didoe should be 1N5819, up to 1A. Good to know it is fixed.
We will work for the low power, will see what we can do best to low the power.
Hi, we will need time to check the low power, not really good at this. We have a replacement IC instead of Atmega328, which should work fully same. but 1.2 usd cheaper. Totally each board could be 1.5-2 usd cheaper for bulk I think.
Hi, Sorry never try the low power for this before, so no idea now, will test this and reply you later.
The wiki login info is sent together with your order tracking info email, please check there.
Hi What is is boardcast message? It is TCP UDP message?
nice, you know how to post code :)
Hi, no need any other special board, just use arduino pro mini 3.3V/8M version as board.
Reply to #1 @ralphxyz :
Hi, Have you updated the firmware? It is working now? Smar-config method has no AP, use instruction here: http://www.electrodragon.com/w/ESP_Board_Setup
Any custom items you need can upload image here, better with a model name or key name for search. Thanks!
Tested with our FTDI basic version cable, using ESP download tool, up to 1500000 bps speed.
Homie library - easy config, support OTA, well supported MQTT, etc
These items will be sold on low price to clear stock, new better items comming soon!
2017/09/22
http://www.electrodragon.com/product/raspberry-pi-sim800-gsm-gprs-add-v2-
We used with IP address, it is working fine. Not tired with domain name, sorry not sure about this ..